Datasheet MAT02 (Analog Devices) - 6
| Hersteller | Analog Devices |
| Beschreibung | Low Noise, Matched Dual Monolithic Transistor |
| Seiten / Seite | 12 / 6 — MAT02. LOG CONFORMANCE TESTING. OBSOLETE |
| Revision | E |
| Dateiformat / Größe | PDF / 788 Kb |
| Dokumentensprache | Englisch |
MAT02. LOG CONFORMANCE TESTING. OBSOLETE
Modelllinie für dieses Datenblatt
Textversion des Dokuments
MAT02
Figure 1. Log Conformance Test Circuit
LOG CONFORMANCE TESTING
kT IC1 The log conformance of the MAT02 is tested using the circuit ∆V In BE = + I q I C1 rBE1 – IC2 rBE2 (2) shown above. The circuit employs a dual transdiode logarithmic C2 converter operating at a fixed ratio of collector currents that are A ramp function that sweeps from 1 V to 10 V is converted by swept over a 10:1 range. The output of each transdiode converter the op amps to a collector current ramp through each transistor. is the VBE of the transistor plus an error term which is the prod- Because IC1 is made equal to 10 IC2, and assuming TA = 25°C, uct of the collector current and rBE, the bulk emitter resistance. the previous equation becomes: The difference of the VBE is amplified at a gain of ×100 by the ∆VBE = 59 mV + 0.9 IC1 rBE (∆rBE ~ 0) AMP01 instrumentation amplifier. The differential emitter-base voltage (∆V As viewed on an oscilloscope, the change in ∆VBE for a 10:1 BE) consists of a temperature-dependent dc level plus an ac error voltage, which is the deviation from true log confor- change in IC is then displayed as shown in Figure 2 below: mity as the collector currents vary. The output of the transdiode logarithmic converter comes from the idealized intrinsic transistor equation (for silicon):
OBSOLETE
kT I V = In C BE (1) q IS where Figure 2. k = Boltzmann’s Constant (1.38062 × 10–23 J/K) With the oscilloscope ac coupled, the temperature dependent term becomes a dc offset and the trace represents the deviation q = Unit Electron Charge (1.60219 × 10–19 °C) from true log conformity. The bulk resistance can be calculated T = Absolute Temperature, K (= °C + 273.2) from the voltage deviation ∆VO and the change in collector I current (9 mA): S = Extrapolated Current for VBE→0 IC = Collector Current ∆VO r × 1 (3) An error term must be added to this equation to allow for the BE = 9mA 100 bulk resistance (rBE) of the transistor. Error due to the op amp This procedure finds r input current is limited by use of the OP15 BiFET-input op BE for Side A. Switching R1 and R2 will provide the r amp. The resulting AMP01 input is: BE for Side B. Differential rBE is found by making R1 = R2. –6– REV. E
Figure 1. Log Conformance Test Circuit
LOG CONFORMANCE TESTING
kT IC1 The log conformance of the MAT02 is tested using the circuit ∆V In BE = + I q I C1 rBE1 – IC2 rBE2 (2) shown above. The circuit employs a dual transdiode logarithmic C2 converter operating at a fixed ratio of collector currents that are A ramp function that sweeps from 1 V to 10 V is converted by swept over a 10:1 range. The output of each transdiode converter the op amps to a collector current ramp through each transistor. is the VBE of the transistor plus an error term which is the prod- Because IC1 is made equal to 10 IC2, and assuming TA = 25°C, uct of the collector current and rBE, the bulk emitter resistance. the previous equation becomes: The difference of the VBE is amplified at a gain of ×100 by the ∆VBE = 59 mV + 0.9 IC1 rBE (∆rBE ~ 0) AMP01 instrumentation amplifier. The differential emitter-base voltage (∆V As viewed on an oscilloscope, the change in ∆VBE for a 10:1 BE) consists of a temperature-dependent dc level plus an ac error voltage, which is the deviation from true log confor- change in IC is then displayed as shown in Figure 2 below: mity as the collector currents vary. The output of the transdiode logarithmic converter comes from the idealized intrinsic transistor equation (for silicon):
OBSOLETE
kT I V = In C BE (1) q IS where Figure 2. k = Boltzmann’s Constant (1.38062 × 10–23 J/K) With the oscilloscope ac coupled, the temperature dependent term becomes a dc offset and the trace represents the deviation q = Unit Electron Charge (1.60219 × 10–19 °C) from true log conformity. The bulk resistance can be calculated T = Absolute Temperature, K (= °C + 273.2) from the voltage deviation ∆VO and the change in collector I current (9 mA): S = Extrapolated Current for VBE→0 IC = Collector Current ∆VO r × 1 (3) An error term must be added to this equation to allow for the BE = 9mA 100 bulk resistance (rBE) of the transistor. Error due to the op amp This procedure finds r input current is limited by use of the OP15 BiFET-input op BE for Side A. Switching R1 and R2 will provide the r amp. The resulting AMP01 input is: BE for Side B. Differential rBE is found by making R1 = R2. –6– REV. E