link to page 10 link to page 10 link to page 10 link to page 10 link to page 10 AD586 Figure 18 shows the typical output voltage drift for the AD586L Table 5. Maximum Output Change in mV and illustrates the test methodology. The box in Figure 18 is Maximum Output Change (mV) bounded on the sides by the operating temperature extremes Device and on the top and the bottom by the maximum and minimum Grade0°C to 70°C−40°C to +85°C−55°C to +125°C output voltages measured over the operating temperature AD586J 8.75 range. The slope of the diagonal drawn from the lower left to AD586K 5.25 the upper right corner of the box determines the performance AD586L 1.75 grade of the device. AD586M 0.70 AD586A 9.37 VMAX –VMIN AD586B 3.12 SLOPE = T.C. = (TMAX –TMIN) × 5 × 10–6 AD586S 18.00 5.0027 – 5.0012= (70 ° C – 0) × 5 × 10–6 AD586T 9.00 = 4.3ppm/ ° CTMINTMAXSLOPENEGATIVE REFERENCE VOLTAGE FROM AN AD5865.003VMAX The AD586 can be used to provide a precision −5.000 V output, as shown in Figure 19. The VIN pin is tied to at least a 6 V supply, the output pin is grounded, and the AD586 ground pin is con- VMIN nected through a resistor, RS, to a −15 V supply. The −5 V output is now taken from the ground pin (Pin 4) instead of VOUT. It is 5.000 essential to arrange the output load and the supply resistor, RS, so that the net current through the AD586 is between 2.5 mA and 10.0 mA. The temperature characteristics and long-term –20020406080TEMPERATURE ( ° C) 00625-017 stability of the device will be essentially the same as that of a unit used in the standard +5 V output configuration. Figure 18. Typical AD586L Temperature Drift +6V → +30V10V2.5mA <–I Each AD586J, AD586K, and AD586L grade unit is tested at 0°C, L < 10mARS2 25°C, and 70°C. Each AD586SQ and AD586TQ grade unit is VIN tested at −55°C, +25°C, and +125°C. This approach ensures that AD586VOUT 6 the variations of output voltage that occur as the temperature GND changes within the specified range will be contained within a 4IL box whose diagonal has a slope equal to the maximum specified –5V drift. The position of the box on the vertical scale will change RS from device to device as initial error and the shape of the curve –15V 00529-018 vary. The maximum height of the box for the appropriate tem- Figure 19. AD586 as a Negative 5 V Reference perature range and device grade is shown in Table 5. Dupli- cation of these results requires a combination of high accuracy USING THE AD586 WITH CONVERTERS and stable temperature control in a test system. Evaluation of The AD586 is an ideal reference for a wide variety of 8-, 12-, 14-, the AD586 will produce a curve similar to that in Figure 18, but and 16-bit ADCs and DACs. Several representative examples are output readings could vary depending on the test methods and explained in the following sections. equipment used. Rev. G | Page 10 of 16 Document Outline FEATURES GENERAL DESCRIPTION PRODUCT HIGHLIGHTS SPECIFICATIONS AD586J, AD586K/AD586A, AD586L/AD586B AD586M, AD586S, AD586T ABSOLUTE MAXIMUM RATINGS ESD CAUTION PIN CONFIGURATIONS AND FUNCTION DESCRIPTIONS THEORY OF OPERATION APPLYING THE AD586 NOISE PERFORMANCE AND REDUCTION TURN-ON TIME DYNAMIC PERFORMANCE LOAD REGULATION TEMPERATURE PERFORMANCE NEGATIVE REFERENCE VOLTAGE FROM AN AD586 USING THE AD586 WITH CONVERTERS 5 V REFERENCE WITH MULTIPLYINGCMOS DACs OR ADCs STACKED PRECISION REFERENCES FORMULTIPLE VOLTAGES PRECISION CURRENT SOURCE PRECISION HIGH CURRENT SUPPLY OUTLINE DIMENSIONS ORDERING GUIDE