Datasheet LT1027 (Analog Devices) - 3
| Hersteller | Analog Devices |
| Beschreibung | Precision 5 Volt Reference |
| Seiten / Seite | 8 / 3 — ELECTRICAL CH. ARA TERISTICS The. denotes specifications which apply over … |
| Dateiformat / Größe | PDF / 220 Kb |
| Dokumentensprache | Englisch |
ELECTRICAL CH. ARA TERISTICS The. denotes specifications which apply over the full operating
Modelllinie für dieses Datenblatt
Textversion des Dokuments
LT1027
ELECTRICAL CH C ARA TERISTICS The
●
denotes specifications which apply over the full operating temperature range otherwise specifications are at TA = 25
°
C. VIN = 10V, ILOAD = 0, unless otherwise specified. SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS
Line Regulation (Note 4) 8V ≤ VIN ≤ 10V 6 12 ppm/V ● 25 ppm/V 10V ≤ VIN ≤ 40V 3 6 ppm/V ● 8 ppm/V Load Regulation (Notes 4, 6) Sourcing Current –8 –3 6 ppm/mA 0 ≤ IOUT ≤ 15mA ● –10 8 ppm/mA Sinking Current ● 30 120 ppm/mA 0 ≥ IOUT ≥ – 10mA Supply Current 2.2 3.1 mA ● 3.5 mA VTRIM Adjust Range ● ±30 ±50 mV en Output Noise (Note 5) 0.1Hz ≤ f ≤ 10Hz 3 µVP-P 10Hz ≤ f ≤ 1kHz 2.0 6.0 µVRMS Temperature Hysteresis H package; ∆T = 25°C 10 ppm Long Term Stability H package 20 ppm/month
Note 1:
Absolute Maximum Ratings are those values beyond which the life
Note 5:
RMS noise is measured with an 8-pole bandpass filter with a of the part may be impaired. center frequency of 30Hz and a Q of 1.5. The filter output is then rectified and integrated for a fixed time period, resulting in an average, as opposed
Note 2:
Output voltage is measured immediately after turn-on. Changes to RMS voltage. A correction factor is used to convert average to RMS. due to chip warm-up are typically less than 0.005%. This value is then used to obtain RMS noise voltage in the 10Hz to 1000Hz
Note 3:
Temperature coefficient is determined by the "box" method in frequency band. This test also screens for low frequency "popcorn" noise which the maximum ∆VOUT over the temperature range is divided by ∆T. within the bandwidth of the filter. Consult factory for 100% 0.1Hz to 10Hz
Note 4:
Line and load regulation measurements are done on a pulse basis. noise testing. Output voltage changes due to die temperature change must be taken into
Note 6:
Devices typically exhibit a slight negative DC output impedance of account separately. Package thermal resistance is 150°C/W for TO-5 (H), – 0.015Ω. This compensates for PC trace resistance, improving regulation 130°C/W for PDIP (N8), and 180°C/W for plastic SO (SO-8). at the load.
W U TYPICAL PERFOR A CE CH C ARA TERISTICS Ripple Rejection Output Impedance vs Frequency Output Voltage
100 100 5.006 V ∆I = ±3mA AC IN = 10V 120 ISOURCE = 5mA 5.004 110 ) Ω 10 5.002 100 90 1 5.000 80 REJECTION (dB) 4.998 OUTPUT VOLTAGE (V) 70 OUTPUT IMPEDANCE ( 0.1 4.996 60 0.01 50 4.994 10 100 1k 10k 10 100 1k 10k 100k 1M –50 –25 0 25 50 75 100 FREQUENCY (Hz) FREQUENCY (Hz) TEMPERATURE (°C) 1027 G01 1027 G02 1027 G03 sn1027 1027fcs 3
ELECTRICAL CH C ARA TERISTICS The
●
denotes specifications which apply over the full operating temperature range otherwise specifications are at TA = 25
°
C. VIN = 10V, ILOAD = 0, unless otherwise specified. SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS
Line Regulation (Note 4) 8V ≤ VIN ≤ 10V 6 12 ppm/V ● 25 ppm/V 10V ≤ VIN ≤ 40V 3 6 ppm/V ● 8 ppm/V Load Regulation (Notes 4, 6) Sourcing Current –8 –3 6 ppm/mA 0 ≤ IOUT ≤ 15mA ● –10 8 ppm/mA Sinking Current ● 30 120 ppm/mA 0 ≥ IOUT ≥ – 10mA Supply Current 2.2 3.1 mA ● 3.5 mA VTRIM Adjust Range ● ±30 ±50 mV en Output Noise (Note 5) 0.1Hz ≤ f ≤ 10Hz 3 µVP-P 10Hz ≤ f ≤ 1kHz 2.0 6.0 µVRMS Temperature Hysteresis H package; ∆T = 25°C 10 ppm Long Term Stability H package 20 ppm/month
Note 1:
Absolute Maximum Ratings are those values beyond which the life
Note 5:
RMS noise is measured with an 8-pole bandpass filter with a of the part may be impaired. center frequency of 30Hz and a Q of 1.5. The filter output is then rectified and integrated for a fixed time period, resulting in an average, as opposed
Note 2:
Output voltage is measured immediately after turn-on. Changes to RMS voltage. A correction factor is used to convert average to RMS. due to chip warm-up are typically less than 0.005%. This value is then used to obtain RMS noise voltage in the 10Hz to 1000Hz
Note 3:
Temperature coefficient is determined by the "box" method in frequency band. This test also screens for low frequency "popcorn" noise which the maximum ∆VOUT over the temperature range is divided by ∆T. within the bandwidth of the filter. Consult factory for 100% 0.1Hz to 10Hz
Note 4:
Line and load regulation measurements are done on a pulse basis. noise testing. Output voltage changes due to die temperature change must be taken into
Note 6:
Devices typically exhibit a slight negative DC output impedance of account separately. Package thermal resistance is 150°C/W for TO-5 (H), – 0.015Ω. This compensates for PC trace resistance, improving regulation 130°C/W for PDIP (N8), and 180°C/W for plastic SO (SO-8). at the load.
W U TYPICAL PERFOR A CE CH C ARA TERISTICS Ripple Rejection Output Impedance vs Frequency Output Voltage
100 100 5.006 V ∆I = ±3mA AC IN = 10V 120 ISOURCE = 5mA 5.004 110 ) Ω 10 5.002 100 90 1 5.000 80 REJECTION (dB) 4.998 OUTPUT VOLTAGE (V) 70 OUTPUT IMPEDANCE ( 0.1 4.996 60 0.01 50 4.994 10 100 1k 10k 10 100 1k 10k 100k 1M –50 –25 0 25 50 75 100 FREQUENCY (Hz) FREQUENCY (Hz) TEMPERATURE (°C) 1027 G01 1027 G02 1027 G03 sn1027 1027fcs 3