Datasheet Texas Instruments MSP430FR2111 — Datenblatt

Hersteller	Texas Instruments
Serie	MSP430FR2111

Datenblätter

Preise

Status

Verpackung

Parameter

Parameters / Models	MSP430FR2111IPW16	MSP430FR2111IPW16R	MSP430FR2111IRLLR	MSP430FR2111IRLLT
ADC	ADC10 - 8ch	ADC10 - 8ch	ADC10 - 8ch	ADC10 - 8ch
AES	N/A	N/A	N/A	N/A
Active Power, uA/MHz	120	120	120	120
Additional Features	Real-Time Clock,Watchdog,Temp Sensor,Brown Out Reset	Real-Time Clock,Watchdog,Temp Sensor,Brown Out Reset	Real-Time Clock,Watchdog,Temp Sensor,Brown Out Reset	Real-Time Clock,Watchdog,Temp Sensor,Brown Out Reset
BSL	UART	UART	UART	UART
CPU	MSP430	MSP430	MSP430	MSP430
Comparators	4	4	4	4
Featured	fr2	fr2	fr2	fr2
Frequency, MHz	16	16	16	16
GPIO Pins	12	12	12	12
Max VCC	3.6	3.6	3.6	3.6
Min VCC	1.8	1.8	1.8	1.8
Multiplier	N/A	N/A	N/A	N/A
Non-volatile Memory, KB	4	4	4	4
Operating Temperature Range, C	-40 to 85	-40 to 85	-40 to 85	-40 to 85
Package Group	TSSOP	TSSOP	VQFN	VQFN
Package Size: mm2:W x L, PKG	16TSSOP: 32 mm2: 6.4 x 5(TSSOP)	16TSSOP: 32 mm2: 6.4 x 5(TSSOP)	24VQFN: 9 mm2: 3 x 3(VQFN)	24VQFN: 9 mm2: 3 x 3(VQFN)
RAM, KB	1	1	1	1
Rating	Catalog	Catalog	Catalog	Catalog
SPI	1	1	1	1
Security Enabler	Cryptographic acceleration,Debug security,Physical security,Secure FW and SW update,Software IP protection	Cryptographic acceleration,Debug security,Physical security,Secure FW and SW update,Software IP protection	Cryptographic acceleration,Debug security,Physical security,Secure FW and SW update,Software IP protection	Cryptographic acceleration,Debug security,Physical security,Secure FW and SW update,Software IP protection
Special I/O	N/A	N/A	N/A	N/A
Standby Power, LPM3-uA	1	1	1	1
Timers - 16-bit	1	1	1	1
UART	1	1	1	1
Wakeup Time, us	10	10	10	10

Öko-Plan

Anwendungshinweise

• Herunterladen
  Software I2C Master and Slave on MSP430FR2111
  PDF, 348 Kb, Datei veröffentlicht: Aug 10, 2016
  The MSP430FR2111 is an FRAM-based low-pin-count (16 pins) microcontroller of the MSP430FRx family. Because of its low pin count, the hardware I2C module is not integrated in this MCU. This application report describes a software-based I2C solution for the MSP430FR2111 MCU. Both software I2C master and slave solutions are implemented using a small amount of MCU resources. The interface to the I2C b
• Herunterladen
  VLO Calibration on the MSP430FR4xx and MSP430FR2xx Family (Rev. A)
  PDF, 78 Kb, Revision: A, Datei veröffentlicht: Feb 19, 2016
  MSP430FR4xx and MSP430FR2xx (FR4xx/FR2xx) family microcontrollers (MCUs) provide various clock sources, including some high-speed high-accuracy clocks and some low-power low-system-cost clocks. Users can select the best balance of performance, power consumption, and system cost. The on-chip very low-frequency oscillator (VLO) is a clock source with 10-kHz typical frequency included in FR4xx/FR2xx
• Herunterladen
  MSP430 FRAM Technology – How To and Best Practices
  PDF, 326 Kb, Datei veröffentlicht: Jun 23, 2014
  FRAM is a non-volatile memory technology that behaves similar to SRAM while enabling a whole host of new applications, but also changing the way firmware should be designed. This application report outlines the how to and best practices of using FRAM technology in MSP430 from an embedded software development perspective. It discusses how to implement a memory layout according to application-specif
• Herunterladen
  MSP430 FRAM Quality and Reliability (Rev. A)
  PDF, 295 Kb, Revision: A, Datei veröffentlicht: May 1, 2014
  FRAM is a nonvolatile embedded memory technology and is known for its ability to be ultra-low power while being the most flexible and easy-to-use universal memory solution available today. This application report is intended to give new FRAM users and those migrating from flash-based applications knowledge on how FRAM meets key quality and reliability requirements such as data retention and endura
• Herunterladen
  Migrating From MSP430 F2xx and G2xx Families to MSP430 FR4xx and FR2xx Family (Rev. E)
  PDF, 237 Kb, Revision: E, Datei veröffentlicht: May 4, 2018
  This application report helps to ease the migration from MSP430F2xx flash-based MCUs to the MSP430FR4xx and MSP430FR2xx family of FRAM-based MCUs. It discusses programming system hardware core architecture and peripheral considerations. The intent is to highlight key differences between the two families. For more information on the use of the MSP430FR4xx and MSP430FR2xx devices see the MSP430
• Herunterladen
  General Oversampling of MSP ADCs for Higher Resolution (Rev. A)
  PDF, 551 Kb, Revision: A, Datei veröffentlicht: Apr 1, 2016
  Multiple MSP ultra-low-power microcontrollers offer analog-to-digital converters (ADCs) to convert physical quantities into digital numbers, a function that is widely used across numerous applications. There are times, however, when a customer design demands a higher resolution than the ADC of the selected MSP can offer. This application report, which is based on the previously-published Oversampl

Modellreihe

Herstellerklassifikation

• Semiconductors> Microcontrollers (MCU)> MSP430 ultra-low-power MCUs> MSP430FRxx FRAM