Datasheet Texas Instruments TPS60250RTER — Datenblatt

HerstellerTexas Instruments
SerieTPS60250
ArtikelnummerTPS60250RTER
Datasheet Texas Instruments TPS60250RTER

Hocheffiziente Ladepumpe für 7 WLEDs mit I2C-Schnittstelle 16-WQFN -40 bis 85

Datenblätter

High Efficiency Charge Pump for 7 WLEDs with I2C Interface datasheet
PDF, 887 Kb, Revision: C, Datei veröffentlicht: Apr 23, 2008
Auszug aus dem Dokument

Preise

Status

Lifecycle StatusActive (Recommended for new designs)
Manufacture's Sample AvailabilityYes

Verpackung

Pin16
Package TypeRTE
Industry STD TermWQFN
JEDEC CodeS-PQFP-N
Package QTY3000
CarrierLARGE T&R
Device MarkingBSR
Width (mm)3
Length (mm)3
Thickness (mm).75
Pitch (mm).5
Max Height (mm).8
Mechanical DataHerunterladen

Parameter

Number of Channels7
Duty Cycle(Max)0.23 %
LED4+2+1
LED Current Per Channel25 mA
Operating Temperature Range-40 to 85 C
Package GroupWQFN
Package Size: mm2:W x L16WQFN: 9 mm2: 3 x 3(WQFN) PKG
Peak Efficiency93 %
RatingCatalog
Shutdown Current(Typ)0.1 uA
Special FeaturesAnalog Dimming,Enable/Shutdown,I2C Control,Integrated Switch,Load Disconnect During Shutdown,OVP,Soft Start,Synchronous Rectification
Switching Frequency(Max)875 kHz
TopologyBoost
TypeCapacitive
Vin(Max)6 V
Vin(Min)3 V
Vout(Max)6.5 V
Vout(Min)2.7 V

Öko-Plan

RoHSCompliant

Design Kits und Evaluierungsmodule

  • Evaluation Modules & Boards: TPS60250EVM-185
    TPS60250 Evaluation Module
    Lifecycle Status: Active (Recommended for new designs)

Anwendungshinweise

  • MSP430 Interface to TPS60250 via I2C Master Software
    PDF, 499 Kb, Datei veröffentlicht: May 1, 2008
    The TPS60250 is a high-efficiency, constant-frequency charge pump dc/dc converter that can drive up to five white LEDs for a main display and up to two white LEDs for a subdisplay with regulated constant current for uniform intensity.A microcontroller (MCU) can be used to control the currents for white LEDs via the TPS60250 charge pump through a standard I2C interface, with the MCU acting as t
  • Ballast Resistor Calculation – Current Matching in Parallel LEDs
    PDF, 351 Kb, Datei veröffentlicht: Apr 16, 2009
    Engineers often need to connect LEDs in parallel. Ideally, the LEDs share current equally. In reality, even LEDs from the same production lot have poorly matched I-V characteristics. This mismatch causes the LEDs to not share the current equally. The engineer can add a ballast resistor in series with each LED to minimize current differences. This application report explains how to size the ball
  • Extending the Soft Start Time Without a Soft Start Pin (Rev. B)
    PDF, 387 Kb, Revision: B, Datei veröffentlicht: Jun 15, 2017
  • Performing Accurate PFM Mode Efficiency Measurements (Rev. A)
    PDF, 418 Kb, Revision: A, Datei veröffentlicht: Dec 11, 2018
    When performing measurements on DC-DC converters using pulse frequency modulation(PFM)or any power save mode proper care must be taken to ensure that the measurements are accurate. An accurate PFM mode efficiency measurement is critical for systems which require high efficiency at low loads such as in smart home systems tablets wearables and metering.

Modellreihe

Serie: TPS60250 (2)

Herstellerklassifikation

  • Semiconductors > Power Management > LED Driver > Backlight LED Driver