Vierzweck-Operationsverstärker 14-PDIP 0 bis 70
PDF, 88 Kb, Datei veröffentlicht: Oct 1, 2002
PDF, 254 Kb, Datei veröffentlicht: May 10, 2004
PDF, 727 Kb, Revision: C, Datei veröffentlicht: May 1, 2013
This application note is a guide for Op Amps. The circuits discussed herein are illustrative of the versatilityof the integrated operational amplifier and provide a guide to a number of useful applications. Thecautions noted in each section will show the more common pitfalls encountered in amplifier usage.
PDF, 1.2 Mb, Datei veröffentlicht: May 10, 2004
Application Note 24 A Simplified Test Set for Op Amp Characterization
PDF, 965 Kb, Revision: B, Datei veröffentlicht: May 1, 2013
This application note describes a monolithic operational amplifier which has input error currents in theorder of 100 pA over a в€’55В°C to 125В°C temperature range. Instead of FETs, the circuit used bipolartransistors with current gains of 5000 so that offset voltage and drift are not degraded. A powerconsumption of 1 mW at low voltage is also featured.A number of novel circuits that make use
PDF, 579 Kb, Revision: B, Datei veröffentlicht: May 1, 2013
Operational amplifiers are undoubtedly the easiest and best way of performing a wide range of linearfunctions from simple amplification to complex analog computation. The cost of monolithic amplifiers isnow less than $2.00, in large quantities, which makes it attractive to design them into circuits where theywould not otherwise be considered. Yet low cost is not the only attraction of monoli
PDF, 2.3 Mb, Revision: B, Datei veröffentlicht: May 1, 2013
This application report provides basic circuits of the Texas Instruments op amp collection.
PDF, 169 Kb, Datei veröffentlicht: May 3, 2004
Application Note 241 Working with High Impedance Op Amps
PDF, 142 Kb, Datei veröffentlicht: May 10, 2004
Application Brief 24 Bench Testing LM3900 and LM359 Input Parameters
PDF, 782 Kb, Datei veröffentlicht: May 10, 2004
Application Note 446 A 150W IC Op Amp Simplifies Design of Power Circuits
PDF, 1.2 Mb, Revision: A, Datei veröffentlicht: Sep 19, 2016
It is well known that the voltage noise of an operational amplifier can be decreased by increasing the emitter currentof the input stage. The signal-to-noise ratio will be improved by the increase of bias, until the base current noise begins to dominate.
PDF, 379 Kb, Datei veröffentlicht: May 11, 2004
PDF, 94 Kb, Datei veröffentlicht: Oct 3, 2002
PDF, 80 Kb, Datei veröffentlicht: Oct 2, 2002
PDF, 314 Kb, Datei veröffentlicht: May 14, 2004
PDF, 71 Kb, Datei veröffentlicht: Oct 2, 2002
PDF, 139 Kb, Datei veröffentlicht: Oct 7, 2002
PDF, 502 Kb, Revision: B, Datei veröffentlicht: May 5, 2013
This application report discusses how combining an “inferior”, 20 year old A/D conversion technique with amicroprocessor, a developmental A/D converter achieves 1 part-per-million (20-bit) linearity.
PDF, 421 Kb, Datei veröffentlicht: Oct 4, 2004
PDF, 370 Kb, Revision: B, Datei veröffentlicht: May 1, 2013
One of the most predictable non-linear elements commonly available is the bipolar transistor. Therelationship between collector current and emitter base voltage is precisely logarithmic from currentsbelow one picoamp to currents above one milliamp. Using a matched pair of transistors and integratedcircuit operational amplifiers it is relatively easy to construct a linear to logarithmic conv
PDF, 867 Kb, Revision: B, Datei veröffentlicht: Apr 23, 2013
This application note provides new design ideas and discusses the positive impact of designing with theDual Norton amplifier.
PDF, 940 Kb, Revision: B, Datei veröffentlicht: May 1, 2013
Since the introduction of monolithic IC amplifiers there has been a continual improvement in DC accuracy.Bias currents have been decreased by 5 orders of magnitude over the past 5 years. Low offset voltagedrift is also necessary in a high accuracy circuits. This is evidenced by the popularity of low drift amplifiertypes as well as the requests for selected low-drift op amps. However until n
PDF, 966 Kb, Revision: B, Datei veröffentlicht: May 5, 2013
This application report discusses how a super matched bipolar transistor pair sets new standards for driftand noise.
PDF, 218 Kb, Datei veröffentlicht: May 11, 2004
PDF, 272 Kb, Datei veröffentlicht: May 2, 2004
PDF, 107 Kb, Datei veröffentlicht: Oct 2, 2002
PDF, 1.1 Mb, Revision: B, Datei veröffentlicht: May 6, 2013
The availability of dual and quad packaged FET op amps offers the designer all the traditional capabilitiesof FET op amps including low bias current and speed and some additional advantages. The cost-peramplifieris lower because of reduced package costs. This means that more amplifiers are available toimplement a function at a given cost making design easier. At the same time the availab
PDF, 273 Kb, Datei veröffentlicht: Jul 13, 1998
Selecting the right operational amplifier for a specific application requires you to have your design goals clearly in mind along with a firm understanding of what the published specifications mean. This paper addresses the issue of understanding data sheet specifications.This paper begins with background information. First introductory topics on the basic principles of amplifiers are presen
PDF, 2.8 Mb, Revision: B, Datei veröffentlicht: Sep 19, 2016
While in the process of reviewing Texas Instruments applications notes including those from Burr-Brown - I uncovered a couple of treasures this handbook on op amp applications and one on active RC networks. These old publications from 1963 and 1966 respectively are some of the finest works on op amp theory that I have ever seen. Nevertheless they contain some material that is hopelessly outd
PDF, 747 Kb, Revision: C, Datei veröffentlicht: Apr 22, 2013
This application note describes the sine wave generation techniques to control frequency amplitude anddistortion levels.
PDF, 262 Kb, Revision: B, Datei veröffentlicht: May 6, 2013
Of all common environmental parameters humidity is perhaps the least understood and most difficult tomeasure. The most common electronic humidity detection methods albeit highly accurate are not obviousand tend to be expensive and complex (See Box). Accurate humidity measurement is vital to a number ofdiverse areas including food processing paper and lumber production pollution monitor
PDF, 91 Kb, Datei veröffentlicht: Oct 2, 2002