Datasheet Texas Instruments LM3481MMX/NOPB — Datenblatt
| Hersteller | Texas Instruments |
| Serie | LM3481 |
| Artikelnummer | LM3481MMX/NOPB |
Hocheffizienter Regler für Boost-, SEPIC- und Flyback-DC-DC-Wandler 10-VSSOP -40 bis 125
Datenblätter
LM3481 / -Q1 High-Efficiency Controller for Boost, SEPIC and Flyback DC-DC Converters datasheet
PDF, 1.5 Mb, Revision: F, Datei veröffentlicht: Nov 5, 2012
Auszug aus dem Dokument
Preise
Status
| Lifecycle Status | Active (Recommended for new designs) |
| Manufacture's Sample Availability | No |
Verpackung
| Pin | 10 |
| Package Type | DGS |
| Industry STD Term | VSSOP |
| JEDEC Code | S-PDSO-G |
| Package QTY | 3500 |
| Carrier | LARGE T&R |
| Device Marking | SJPB |
| Width (mm) | 3 |
| Length (mm) | 3 |
| Thickness (mm) | 1.02 |
| Pitch (mm) | .5 |
| Max Height (mm) | 1.07 |
| Mechanical Data | Herunterladen |
Parameter
| Duty Cycle(Max) | 85 % |
| Iout(Max) | 10 A |
| Iq(Typ) | 3.7 mA |
| Operating Temperature Range | -40 to 125 C |
| Package Group | VSSOP |
| Rating | Catalog |
| Regulated Outputs | 1 |
| Special Features | Adjustable Current Limit,Enable,Frequency Synchronization,Light Load Efficiency,Pre-Bias Start-Up,UVLO Adjustable |
| Switch Current Limit(Typ) | 10 A |
| Switching Frequency(Max) | 1000 kHz |
| Switching Frequency(Min) | 100 kHz |
| Type | Controller |
| Vin(Max) | 48 V |
| Vin(Min) | 2.97 V |
| Vout(Max) | 500 V |
| Vout(Min) | 1.275 V |
Öko-Plan
| RoHS | Compliant |
Design Kits und Evaluierungsmodule
- Evaluation Modules & Boards: LM3481EVAL
High Efficiency Boost Switching Controller Eval Board with 12 Volt Output
Lifecycle Status: Active (Recommended for new designs) - Evaluation Modules & Boards: LM3481SEPICEVAL
LM3481 SEPIC Evaluation Board
Lifecycle Status: Active (Recommended for new designs) - Evaluation Modules & Boards: LM3481-FLYBACKEVM
Isolated Flyback Topology Evaluation Module for LM3481 Boost Controller
Lifecycle Status: Active (Recommended for new designs)
Anwendungshinweise
- Softstart Using Constant Current Constant Voltage ApproachPDF, 337 Kb, Datei veröffentlicht: Jul 24, 2015
In many systems backup power is provided either by batteries or simply by a large value capacitor. Inthese applications the capacitor would only provide the current when the primary power source fails.Further, these applications are usually for light load currents. During normal operation the backupcapacitors are kept charged up by a DC/DC converter. The challenge involved in an application - Demystifying Type II and Type III Compensators Using Op-Amp and OTA for DC/DC CoPDF, 782 Kb, Datei veröffentlicht: Jul 11, 2014
- AN-1286 Compensation For The LM3478 Boost Controller (Rev. C)PDF, 356 Kb, Revision: C, Datei veröffentlicht: Apr 23, 2013
The LM3478 is a low side N-Channel controller for switching regulators. Like many switching controllers,the added flexibility in component selection can cause problems for users when determining thecompensation scheme. It is the goal of this application report to present a decent groundwork to allow thereader to select with confidence the correct compensation components. To achieve this we l - AN-1484 Designing A SEPIC Converter (Rev. E)PDF, 220 Kb, Revision: E, Datei veröffentlicht: Apr 23, 2013
In a single ended primary inductance converter (SEPIC) design, the output voltage can be higher or lowerthan the input voltage. The SEPIC converter shown in Figure 1 uses two inductors: L1 and L2. The twoinductors can be wound on the same core since the same voltages are applied to them throughout theswitching cycle. - Modeling & Design of Current Mode Control Boost Converters (Rev. B)PDF, 316 Kb, Revision: B, Datei veröffentlicht: Apr 23, 2013
This application note presents a detail modeling and design of current mode control boost convertersoperating in the continuous conduction mode (CCM). Based on the derived small signal models, thedesign of a lag compensator for current mode control boost converters will be detailed. The LM3478 boostcontroller will be used in the example. Simulation and hardware measurement of frequency respo - AN-1990 Compensation for Current Mode Control SEPIC Converters (Rev. A)PDF, 247 Kb, Revision: A, Datei veröffentlicht: Apr 23, 2013
This application note discusses the use of SEPIC converters in various applications. - LM34xx How to Design Flyback Converter with LM3481 Boost ControllerPDF, 1.7 Mb, Datei veröffentlicht: Sep 21, 2016
The TexasInstrumentsLM3481boostcontrolleris a versatilelow-sideN-FEThigh-performancecontrollerfor switchingregulators.Thedevicehaswiderangeof applicationssuchas automotivestart-stopapplication,one-cellor two-cellLi-ionbattery-poweredportableBluetoothaudiosystem,industrialsystemisolatedsupplies,and so forth,and supportstopologi
Modellreihe
Serie: LM3481 (2)
- LM3481MM/NOPB LM3481MMX/NOPB
Herstellerklassifikation
- Semiconductors > Power Management > Non-isolated DC/DC Switching Regulator > Step-Up (Boost) > Boost Controller (External Switch)